EP Sand Buggy "ASB1 CAMO-BLAU" 4WD RTR 1:10 (inkl. Akku/EU-Lader)

 "Dune Bashing" If you want to experience sporty outdoor pleasures, you should do so with the Hot Shot ASB1. If your lawn is nothing but a desert and the stream in front of your door resembles a clay track, then make the most of it - let the ASB1 out! Modelled on the big sand buggies that are all the rage in Dubai, for example, the ASB1 comes with an open cage and lots of driving fun. Jump, race, let the dust fly - do what you like, your ASB1 knows no limits. This is ensured by the best plastic and a completely covered chassis. You also get your charger and the matching battery on top. Treat yourself to the fun of the sheikhs and start your "Dune Bashing".

Features

• 40A waterproof speed controller
• 15T brushed motor
• 2.4 GHz radio control system
• Battery and charger (EU plug)

Features

.
• Fully assembled and equipped all-wheel drive buggy incl. 2.4 GHz remote control, NiMH high-performance battery and charger 
• Waterproof and LiPo-compatible 40A brushed controller with Tamiya connector
• Water-resistant and high-performance steering servo with 4 kg actuating force
• 15 turn brushed motor size 550 with heat sink
• Fully enclosed main drive - prevents the ingress of stones or other foreign bodies
• Aluminium cardan drive with steel mountings
• The vehicle is completely mounted on ball bearings and therefore very smooth-running and durable
• Two cone differentials transmit the torque optimally and compensate for differences in speed, e.g. when cornering.
• Differential outputs made of steel
• The oil pressure shock absorbers can be perfectly adjusted to any track by means of a knurled screw.
• Aluminium engine mount
• Steel CVD shafts on the front axle
• Adjustable track rods via right/left-hand thread
• Chassis stiffening by a dirt cover over the electronics ( controller, receiver and battery )
• 3mm aluminium shock towers V/H
• Prepared for brushless and LiPo operation
• Extremely robust bodyshell ready designed
• The reinforced plastic parts are on the one hand very resistant and on the other hand provide the necessary degree of deformation to survive many an "accident" without damage.


CAUTION: If you want to operate brushed vehicles with a LiPo battery, the battery must not exceed a C-rate of 30C. The controller, motor and connections can otherwise become very hot, which can lead to damage!

Technical data vehicle:

• Dimensions (L/W/H): 430x285x155 mm
• Weight: 2170 g
• Wheelbase: 293 mm
• Ground clearance: 40 mm
• Track front/rear: 230 mm
• Tyre Ø front/rear: ± 105 mm / width 50 mm
• Viscosity damper oil: 400 v/h
• Spring rate damper: medium
• Damper installation length: front 85mm / rear 85mm
• Viscosity differential oil: front 1.000 / rear 3.000
• Internal gear ratio: bevel pinion 13T / ring gear 43T
• Motor ratio: main gear 55T / motor pinion 20T (module 0.8)

Technical data speed controller (ESC):

• Waterproof 40A brushed controller
• NiMH / LiPo operation possible
• Short-time load: 180A
• Function: forward / brake / reverse
• BEC 5V / 2A 
• Operating voltage 7.2 - 7.4V
• Motor limit > 12T at 7.4V; < 30,000 rpm at 7.2V
• Plug-in system: Tamiya

Technical data Thrust ECO motor:

• 15T / 30,000 rpm
• Size 550
• Motor shaft: length 9.6mm; Ø 3.17mm
• Motor dimensions : length 57 mm Ø 36.7 mm 

Technical data servo S40PH:

• Size: Standard
• Actuating force: 4.0 kg @ 4.8V
• Actuating time 0.16 sec / 60° @ 4.8V
• Gear - Nylon
• Gear rim - 25 teeth
• Connector system - JR
• Voltage: 4.8V - 6.6V
• Ball bearing

Remote control technical data:

.
• 2 channel transmitter CR2SV2
• 3 channel mini receiver
• Reverse function
• Dual rate and trim adjustable
• Battery compartment for 4 AA cells (not included)

Scope of delivery:

• 1x Sand Buggy ASB1 RTR BLUE VERSION
• 2.4 GHz remote control CR2SV2
• NiMH Racing Pack
• EU plug-in charger
• Instruction manual

 

Still needed:

• 4 AA mignon cells for remote control